Purchased another towel



Debbie purchased another towel. We like these as they are light to carry and dry fast. 
The towel was ordered from Amazon and is from Sea to Summit; the towel is a DryLite Towel, the color is Eucalyptus, and the size X-Small 





Middle solar panel in place - 2011

October 2011 - At Marina Cortez Harbor Island, San Diego, CA
You can see the flat bar sagging!

Freezer insulation added to top


 Debbie added some Dow Blue Board insulation to the top of the freezer. She glued it in place and we will sand it down to be even or just below the teak that the original lid sits on. This way it will not be hard to get it flush when we fiber glass the area.




New fresh water pump mounting base


 The new fresh water pump (SHURFlo Serial # 5901-2011 Extreme™ Smart Sensor 5.7 Fresh Water Pump) we installed is screwed into the plywood bulkhead in the engine room. It first goes into the 1” insulation. We do not think this is a good way of fastening the pump as it vibrates and after some time will sink into the insulation making the pump loose and then it could vibrate the hoses loose etc. To fix this we are fabricating a piece of marine ½ plywood base which will be under the pump. Also under the pump is a heat sink. The way it presses against the insulation now the heat sink is up against the insulation making it less effective. This mounting plate will remedy all this.






Drilled and sanded




Freezer glassing and refer shelf - 2011

We first sanded and cleaned and sanded some more.

New SHURFlo Smart Sensor 5.7 Fresh Water Pump - 2011

Pump is leaking.
OK so I screwed up and somehow bought an SHURFlo RV pump for our house water pump.
Serial # 5900-2010 and it should have been a Serial # 5901-2011.

Cockpit table


We finally got out cockpit table back form C.S. Furgison. It was late and over budget. He also used screws with round tops instead of flat top screws in the hinges, why? These screws  stick up a bit and make it difficult to slide a plate or mug across tec.
 Darn hard to get things the way you want them at a reasonable cost.






 We are hoping that this is the last custom work to be done. We will probably not go back to C.S. Furgison if we have another project. This kind of work is really not marine specific and go else ware.
It was the hinges that were the problem for us. You need a jig and some experience in this area to make them come out good, we have neither.
 We did use it for breakfast even though we just placed it on top of the existing table. It worked nice as it gave us much more needed room.

Second Kyocera 135 watt solar panel mounted - 2011

October 2011 Marina Kona Kai Shelter Island San Diego, CA
The second Kyocera Solar KD-135GX 135 Watt 12 Volt Solar Electric panel was mounted on top of the bimini. It is a custom fit so it takes a lot longer than we would expect. It is now up there and we also measured for wire lengths.
 Now to get the last 85 watt panel up there and see how they ride is a nice bouncy sail! 😎

SHURFLO Water Pump leaking

 We woke up to our SHURFLO Extreme Series Smart Sensor Water Pump leaking from it's head. Not a goo thing as the water may have gotten into the motor. It is warranted for  3 years from date of manufacturing and we will need to look at the motor to see what date is stamped on it. Also it must be a after market pump meaning we bought it from a store which i think we did. Serial number needs to be 590211.




Bummer


 So that's now a question to be asked. What happens when we are at anchor in Mexico and this pump goes out? We will need to carry a spare? We could use the galley foot pump and also use it to put water into a bucket to pour into the toilet as we have a fresh water flush.
 Looks like a spare pump is the way to go?? 


"SHURflo warrants its 5901 Potable Water pumps to be free from material and workmanship defects under normal use and service
for a period of three (3) years from the date of manufacture indicated on the motor nameplate. The limited warranty will not apply
to pumps that were improperly installed, misapplied, or are incompatible with components not manufactured by SHURflo. Pump
failure due to foreign debris is not covered under the terms of this limited warranty."



SHURflo, LLC Headquarters
5900 Katella Avenue
Cypress, California 90630
Phone (562) 795-5200 ? Toll Free (800) 854-3218
Fax (562) 795-7564

Blue Seas Systems CableClam - 2011

October 2011 - At Marina Cortez Harbor Island, San Diego, CA

 We picked up the Blue Seas Systems CableClam from “Downwind Marine” and also moved the solar panel flat aluminum bracket about an inch so the top stainless steel upright tubes are straight up now.

SaniGard holding tank filter

 We replaced our holding tank filter (10/7/2011). It was originally purchased from Defender Marine on 08/28/2009 and installed around then. This one is the replacement cartridge for 5/8 ends.

 I think they should be replaced every year. Oops!

This last one we got at "A to Z Marine" because we wanted it NOW and WM was out of them J
Nice to have a new one.



 When we bought the original one we also got a re-build kit off eBay and we still have it. We will search it out and re-build the one we used so it will be ready for future use. The kit is just a couple of PVC fittings and some charcoal.  The info is in the kit which I will post. Saves big $$ on filters. We will get the kit and go shop for the kit parts so we have a complete kit and then re-build the old filter. The when the new one fails we can insert the old one (that is re-bulit) and off wego. The we rebuild the one we took off and then we will have a back up again. The we will just need to buy new carbon (I think it comes from fish stores) and foam.



SaniGard SeaLand Dometic Vent Filter RECHARGE KIT for marine holding tanks


Kit includes custom PVC pipe adapters that screw together, special chemical and water resistent foam baffles,
.60 liter of laboratory grade activated carbon and detailed instructions on servicing your previously disposable filter.

This kit allows your filter to last a lifetime rather than 1 year, and allows you to recharge it
yourself for about $5 each time after it has been converted with the kit.




Remove insulation off covers

Finished removing the insulation off the two refer and two freezer covers.










Blue Seas Cable Clam


Going to stop by Downwind Marine and pick up a Blue Seas Cable Clam for the solar panel wires. They need to go through the stern and into the boat.


Blue Sea Cable Clam

  • 1.396" diameter center
  • Ideal for Electronic Instrument Installations
  • Watertight Seal Without Removing Connectors

  • Holding Tank Vent Filter


    Will be stopping by A to Z Marine and pick up a new SEALAND
    SaniGard™ Holding Tank Vent Filter
    5/8 hose size #309310002


    A to Z Marine Service
    atozmarine.net
    (619) 224-1606

    Freezer work


    We worked on the freezer side last night. We got the insulation cut for evaporator plate and are now ready to put in some epoxy to round out the corners. Then it is sanding and fiber glassing, or wait, hold on, I forgot that we want to glue a few pieces of insulation onto the top edges to bring them up to the old height of the lids. This we did not do on the fridge side and it took more work adding fiberglass to do it.
    Forget the more work part!

     Also we removed the old insulation from the top of the fridge led that is closet to the galley. We will fit it and mark it up for the new insulation soon.

    Cap rail caulking


     The starboard side of the cap rail from the big scupper to the stern ladder is now re-caulked. It needs some clean up and then that area is ready for varnish. We also have the upper eye ready for varnish, not that we will do any varnishing soon but are working on having the decks ready for it.


    Got one Kyocera solar panel mounted on bimini - 2011

     We have gotten one Kyocera Solar KD-135GX 135 Watt 12 Volt Solar Electric panel mounted. There is a slight lean to one of the stainless steel 1” cross tubes.

    Air Breeze wind generator came in


    Our new Air Breeze wind generator came in. There is still work to be done mounting the solar panels so the Air Breeze will need to wait a bit to get installed.



    Chula Vista Swap Meet

    The Chula Vista swap meet was OK but smaller than it has been. No rain but few ma and pa sellers. Mostly retailers. They also swoop down on the ma and pa sellers like us as soon as you pull up and try to buy you goods cheap. Then they put them in their both and re-sell them for a lot more.
     We did sell out stuff which was not a lot of stuff and it saved it from going to the land fill and made some bucks. Hinze was selling some stuff (our dock mate) and sold eight port holes and some other items. We split the space rent so that helped. It is a good social experience and some fun. This may be the last one we go to as we really do not need much. We were looking for a basin’s chair and saw one but not something I would ride up the mast in.

    Walking towards us is Steve who is a dock mate





    Also we were looking for a Fortress FX 23 anchor but it was not there.
    I did buy some clamps for hoses and wire cables $2.50 and Debbie got a grate for our grill brand new for $1.00 and that was it. Boy were we or I should say I was good as Debbie does not go crazy like me.




    Solar Panel brackets and fasteners for bimini 1" SS - 2011

     Friday after work I went by the nut and bolt store, the fastener shop,United fasteners and picked up the longer stainless steel screws needed for the solar panel mounts.